Tweet
Seagate hard drive terminal error messages
* The hard drive is detected normally
Interface task reset
1024k x 16 buffer detected ALPINE – 1_Disk S.15 01-16-03 11:51 Head Mask 0000 – Switch to full int. Spin Ready 3.06 05-13-03 14:11 (P)PATA Reset Master
* Undetected due to firmware module loss-ATA loss
Fix: write one donor ATA; ATA module doesn’t affect data.
1024k x 16 buffer detected ALPINE – 1_Disk
M.14 01-16-03 11:51 Head Mask 000F – Switch to full int.
Spin Ready 8.01 04-05-04
(P)PATA Reset
OVERLAY FAILED
* Undetected due to Capacity parameters lost
Fix: Write VEN module or edit the model, power off/on, the hdd should be detected after initialization.
Interface task reset 1024k x 16 buffer detected ALPINE – 1_Disk M.14 01-16-03 11:51 Head Mask 000F – Switch to full int. Spin Ready 8.01 04-05-04 15:38 (P)PATA Reset Stuff Was Unreadable
* For the following messages, it’s suggested to backup the firmware modules first and then force to write modules under command level 1, finally clear G-list.
Interface task reset
1024k x 16 buffer detected ALPINE – 1_Disk S.15 01-16-03 11:51 Head Mask 0000 – Switch to full int. Spin Ready Failed sys sect. write
Failed sys sect. write
Failed sys sect. Write
Master
* 43 47 Errors before hdd recognition
Fix: write VEN module repeatedly
Interface task reset
1024k x 16 buffer detected ALPINE – 1_Disk S.15 01-16-03 11:51 Head Mask 0000 – Switch to full int. Spin Ready AutoRd Err 43 at 700a.00.0001 AutoRd Err 47 at 700a.00.0004
AutoRd Err 43 at 700a.00.0007
AutoRd Err 47 at 700a.00.0009
Master
* Error After HDD Recognition
Fix: Firmware or head failure can output the following message.
Users can load CERT to RAM and next to execute T4E. (Sometimes, after T4E is executed, AGE=60 may occur)
Interface task reset
1024k x 16 buffer detected
ALPINE – 1_Disk M-21 11-25-03 18:53
Buzz – Head Mask FFFF – Switch to full int.
Spin Ready
8.01 09-28-04 15:05
(P)PATA Reset
Master
CE Log EC=43 Rtype=24 OV=0 STStatus0
AT Er 00 Nwt Er 43 RdWr 0018.00.0000
ATA St 50 Er 01 Op 00 0,0000/0/00,00 01 00
Niwot: 00002c2a ff 00002c2a.0.000 00db 0000 e700 0001
CE Log EC=47 Rtype=24 OV=0 STStatus0
AT Er 00 Nwt Er 47 RdWr 0018.00.0000
ATA St 50 Er 01 Op 00 0,0000/0/00,00 01 00
Niwot: 00002c2a ff 00002c2a.0.000 00db 0000 e700 0001
* NOT INTERFACE AGE
This message tells the hdd is under selftest process and we need to check the following AGE value and learn how to move forward.
* AGE=60
AGE=60 is usually caused by a damage in the head adaptive data and failure in loading it. After the drive startup, enter level T command mode, use T>R command
Seagate F3 Terminal Error Messages
7200.12 Thick HDD 1T
Fix No HOST FIS-ReadyStatusFlags
HOST,
No HOST FIS-ReadyStatusFlags 2002A1A5
ASCII Diag mode
* Init SMART Fail
LED:000000CC FAddr:0024E4A3
Reset SMART but fail like following：
F3 1>N1
Init SMART Fail
LED:000000CC FAddr:0024E4A3
LED:000000CC FAddr:0024E4A3
LED:000000CC FAddr:0024E4A3
LED:000000CC FAddr:0024E4A3
(When LED CC occurs, this means the firmware area cannot be accessed and used or interruption during the firmware operation, users are suggested to change one command and try)
* RW: Error processing Performance Parameter File: 203C
No Phy: Staggered spin bypass
* 5400.6 RW Err
RW cmd 0002 req = 19 00 00 00 01 00 00 00 00 00 00 00 19 61 08 00 98 8E 08 00 99 61 08 00
opts = 00001121
RW Err = 43110081
RW cmd 0002 req = 77 49 00 00 01 00 00 00 00 00 00 00 80 AE 05 00 FF AE 05 00 80 AE 05 00
opts = 00001121
RW Err = 43110081
RW cmd 0002 req = 5F 49 00 00 18 00 00 00 00 00 00 00 19 61 08 00 FF FF 17 00 19 61 08 00
opts = 00001121
RW Err = 43110081
RW error suggests usu
st Momentus 750g laptop 2.5” HDD-how to diagnose the Seagate PCB or ROM failure
EarlySpinup Enabled
Rst 0x10M
ExecuteSpinRequest
LED:00000067 FAddr:00380338
LED:00000067 FAddr:00380338^z
LED:00000067 FAddr:00380338^z
LED:00000067 FAddr:00380338
Drive hangs after trying to read firmware. Connect separately the PCB, after the /T appears, the LED 67 error apprears again:
LED:00000067 FAddr:00380338 LED:00000067 FAddr:00380338
So this can be the failure of PCB and ROM.
* 7200.11 RW subfile error 205f Fix
(Message
7200.11
Rst 0x10M
RW subfile error 205f
RW subfile error 205f
ASCII Diag mode
* Rst 0x10M
RW: Disc Ctlr Initialization Completed.
(P) SATA Reset
SIM Error 1009
RW Error 00000080
RAW ON for high temp Temp©=0046
Interface task reset
1024k x 16 buffer detected ALPINE – 1_Disk S.15 01-16-03 11:51 Head Mask 0000 – Switch to full int. Spin Ready 3.06 05-13-03 14:11 (P)PATA Reset Master
* Undetected due to firmware module loss-ATA loss
Fix: write one donor ATA; ATA module doesn’t affect data.
1024k x 16 buffer detected ALPINE – 1_Disk
M.14 01-16-03 11:51 Head Mask 000F – Switch to full int.
Spin Ready 8.01 04-05-04
(P)PATA Reset
OVERLAY FAILED
* Undetected due to Capacity parameters lost
Fix: Write VEN module or edit the model, power off/on, the hdd should be detected after initialization.
Interface task reset 1024k x 16 buffer detected ALPINE – 1_Disk M.14 01-16-03 11:51 Head Mask 000F – Switch to full int. Spin Ready 8.01 04-05-04 15:38 (P)PATA Reset Stuff Was Unreadable
* For the following messages, it’s suggested to backup the firmware modules first and then force to write modules under command level 1, finally clear G-list.
Interface task reset
1024k x 16 buffer detected ALPINE – 1_Disk S.15 01-16-03 11:51 Head Mask 0000 – Switch to full int. Spin Ready Failed sys sect. write
Failed sys sect. write
Failed sys sect. Write
Master
* 43 47 Errors before hdd recognition
Fix: write VEN module repeatedly
Interface task reset
1024k x 16 buffer detected ALPINE – 1_Disk S.15 01-16-03 11:51 Head Mask 0000 – Switch to full int. Spin Ready AutoRd Err 43 at 700a.00.0001 AutoRd Err 47 at 700a.00.0004
AutoRd Err 43 at 700a.00.0007
AutoRd Err 47 at 700a.00.0009
Master
* Error After HDD Recognition
Fix: Firmware or head failure can output the following message.
Users can load CERT to RAM and next to execute T4E. (Sometimes, after T4E is executed, AGE=60 may occur)
Interface task reset
1024k x 16 buffer detected
ALPINE – 1_Disk M-21 11-25-03 18:53
Buzz – Head Mask FFFF – Switch to full int.
Spin Ready
8.01 09-28-04 15:05
(P)PATA Reset
Master
CE Log EC=43 Rtype=24 OV=0 STStatus0
AT Er 00 Nwt Er 43 RdWr 0018.00.0000
ATA St 50 Er 01 Op 00 0,0000/0/00,00 01 00
Niwot: 00002c2a ff 00002c2a.0.000 00db 0000 e700 0001
CE Log EC=47 Rtype=24 OV=0 STStatus0
AT Er 00 Nwt Er 47 RdWr 0018.00.0000
ATA St 50 Er 01 Op 00 0,0000/0/00,00 01 00
Niwot: 00002c2a ff 00002c2a.0.000 00db 0000 e700 0001
* NOT INTERFACE AGE
This message tells the hdd is under selftest process and we need to check the following AGE value and learn how to move forward.
* AGE=60
AGE=60 is usually caused by a damage in the head adaptive data and failure in loading it. After the drive startup, enter level T command mode, use T>R command
Seagate F3 Terminal Error Messages
7200.12 Thick HDD 1T
Fix No HOST FIS-ReadyStatusFlags
HOST,
No HOST FIS-ReadyStatusFlags 2002A1A5
ASCII Diag mode
* Init SMART Fail
LED:000000CC FAddr:0024E4A3
Reset SMART but fail like following：
F3 1>N1
Init SMART Fail
LED:000000CC FAddr:0024E4A3
LED:000000CC FAddr:0024E4A3
LED:000000CC FAddr:0024E4A3
LED:000000CC FAddr:0024E4A3
(When LED CC occurs, this means the firmware area cannot be accessed and used or interruption during the firmware operation, users are suggested to change one command and try)
* RW: Error processing Performance Parameter File: 203C
No Phy: Staggered spin bypass
* 5400.6 RW Err
RW cmd 0002 req = 19 00 00 00 01 00 00 00 00 00 00 00 19 61 08 00 98 8E 08 00 99 61 08 00
opts = 00001121
RW Err = 43110081
RW cmd 0002 req = 77 49 00 00 01 00 00 00 00 00 00 00 80 AE 05 00 FF AE 05 00 80 AE 05 00
opts = 00001121
RW Err = 43110081
RW cmd 0002 req = 5F 49 00 00 18 00 00 00 00 00 00 00 19 61 08 00 FF FF 17 00 19 61 08 00
opts = 00001121
RW Err = 43110081
RW error suggests usu
st Momentus 750g laptop 2.5” HDD-how to diagnose the Seagate PCB or ROM failure
EarlySpinup Enabled
Rst 0x10M
ExecuteSpinRequest
LED:00000067 FAddr:00380338
LED:00000067 FAddr:00380338^z
LED:00000067 FAddr:00380338^z
LED:00000067 FAddr:00380338
Drive hangs after trying to read firmware. Connect separately the PCB, after the /T appears, the LED 67 error apprears again:
LED:00000067 FAddr:00380338 LED:00000067 FAddr:00380338
So this can be the failure of PCB and ROM.
* 7200.11 RW subfile error 205f Fix
(Message
7200.11
Rst 0x10M
RW subfile error 205f
RW subfile error 205f
ASCII Diag mode
* Rst 0x10M
RW: Disc Ctlr Initialization Completed.
(P) SATA Reset
SIM Error 1009
RW Error 00000080
RAW ON for high temp Temp©=0046
Comment